IEI 2000E KEYPAD PROGRAMMING MANUAL MANUAL
IEI 2000E KEYPAD PROGRAMMING MANUAL SERIES

Iei 212i keypad programming manual : features and programming : iei international electronics 212il il style keypad Iei 212i keypad programming manual : changing code on iei keypad 11Linear llc / iei iei-212i fm212 user indooraccess keypad iei. Iei 212se keypad wiring diagram Iei 212w outdoor weatherproof keypad access control 120-user codes Iei 212se keypad programming manual / 1 - Keypad iei reprogram Phone: 80, 78 Fax: 78 Website: Document #: 6104402, Rev 2.Iei 212se keypad programming manual / 1 - Iei 212w keypad programming manual Keypad iei programming diagrams IEI Keypad 212R Indoor / Outdoor Surface-mount Ruggedized - E.D. Then connect the two using 22 AWG stranded and shielded cable. If your Output Module is located more than 18 inches from the keypad (up to a maximum of 100 feet), you must cut the wire harness in half and plug one half into the keypad the other into the Output Module. Wiring the 2000-8EX Output Module If the Output Module is within 18 inches of the keypad, use the 6conductor wire harness, supplied with the Output Module, to make the connection. Programming Keypad Parameters (Default settings are in bold) Command/Action Change Keypad Parameters Keys to Enter/Details 32 # parameter # value # ** Parameter Value 0 – Duress Output Duration 1 – 255 Seconds (default = 5) 1 – Panic Output Duration* 1 – 255 Seconds (default = 5) 2 – Error Lockout Threshold 1 – 50 Attempts (default = 3) 3 – Error Lockout Duration 1 – 255 Seconds (default = 10) 4 – Auto-Entry Count 2 – 10 Digits (default = 4) 7 – Auto-Entry Keypress 2 – 15 Seconds (default = 2) Timeout 10 Using command 10, you can assign any Virtual Output to any Physical Output or disable a Physical Output.Physical Outputs include the main relay and aux relay on the keypad, the eight relays on the 20008EX Output Module and the two audio alerts on the keypad.

Virtual Outputs are functions that you can assign to operate any Physical Output. Exit Program Mode Press: * (Yellow LED Stops Flashing) Programming a Supervisor Code Use the following command sequence to program a supervisor code, which is stored user location 2.Īssigning Virtual Outputs to Physical Outputs (Standalone Mode Only) The keypad is equipped with nineteen Virtual Outputs and twelve Physical Outputs.

Change Master Code Press: 1 # new master code * repeat code * (Yellow LED Flashes Slowly) 3. Enter Program Mode Press: 99 # master code * (Yellow LED Flashes Slowly) 2. 2.Ĭhanging the Master Code The first step in setting up your keypad is to enter program mode and change the master code. Connect the red wire (V+) to the blue wire (common), and then connect them to the positive on the power supply. Wiring an Electric Door Strike (FailSecure) 1. Connect the black wire (V-) to the negative on the Maglock, and then connect them both to the negative on the power supply. Connect the gray wire (normally closed) to the positive on the Maglock. Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction. This section contains information regarding the requirements necessary to meet UL compliance. The 2000e/2000eM keypad is a UL Listed access control unit. Below is a brief explanation of each mode.Ĭircuit Board Diagram UL Requirements Note: J3 is for use only with the 2000-8EX Output Module.

IEI 2000E KEYPAD PROGRAMMING MANUAL SERIES

Keypad Operating Modes 2000 Series The 2000e/2000eM keypad has three operating modes: Standalone e/eM Style Keypad Mode, Secured Series Front End Mode and Wiegand Front End Installation and Programming Guide Mode.

Iei 2000e keypad programming manual